Veteran Garage Door Repair | Keller TX | 817-769-8488

Veteran Garage Door Repair | Keller TX | 817-769-8488

Garage Door Opener Repair

You might find that your garage door opener has actually been giving you problems, so you require to fix it. You can fix it by changing a circuit board, a photo-eye sensing unit, the main drive gear, or the set-limit switches. You can likewise examine if the safety and security sensing units are functioning appropriately.

Changing a circuit card

Replacing a circuit board for your garage door opener calls for a couple of actions and also devices. First, you require to switch off the circuit breaker as well as separate any kind of wires. Next off, open the motherboard cover. This will assist you to identify the problem and determine if you require a brand-new board. Next, remove the old board as well as its cord ports.

You can after that proceed to replace the motherboard. The substitute procedure is easy and also takes around 10 minutes. A brand-new circuit card will certainly cost about $80. To protect your brand-new circuit board from power rises, you can acquire a surge protector.

Replacing a photo-eye sensing unit

Changing a photo-eye sensing unit can be a relatively easy job. Initially, get rid of the sensing unit from the door and also make certain it is positioned properly. If the sensing unit is angled at all, it may not be receiving the proper signal, which could be causing the strobe lights. If you observe that the photo-eyes run out positioning, you may need to have a service technician come and deal with the problem.

The photo-eye sensing unit includes 2 items that install on the outside of the door tracks as well as toward the flooring. The photo eyes will have a tiny LED light and also should be strong in shade. If the light is blinking, its most likely the photo-eye is defective as well as will certainly require to be replaced.

Replacing a primary drive gear

To replace a garage door opener primary drive equipment, beginning by eliminating the cap from the chain sheave. Next off, remove both screws holding the drive equipment to the sprocket assembly. Now, you can loosen the three tension pins. Press them from both sides and afterwards remove them. Then, separate the 3 cords from the garage door opener motor. These cables should be white, red, as well as blue.

Once you have removed the old equipment, set up a brand-new one. Be sure to oil it well. Insert the new equipment right into the shaft, making sure to line up the mounting holes. Make certain the gear as well as gear setting up are positioned appropriately to make certain smooth operation. Next off, utilize a hammer and also a nail to drive a pin right into the brand-new equipment.

Changing the set-limit switches

The very first thing you need to do if your garage door is not functioning correctly is to inspect the set-limit buttons. You may require to change them so that the door closes earlier or stops prior to it gets to the flooring. You can check this by looking at your garage doors manual or online.

To adjust the set-limit buttons, youll need a screwdriver or socket. Readjust the knob clockwise or counterclockwise until the door goes up as well as quits, or lowers its range. To check for correct travel range, determine the void from all-time low of the garage door to the ground.

Veteran Garage Door Repair – Keller

204 S Main St Ste 105, Keller, TX 76248, USA

817-769-8488

https://veterangaragedoor.com/veteran-garage-door-repair-of-keller-tx/


Garage Door Repair


Garage Door Installation


Garage Door Company


Garage Door Service


Garage Door Opener Repair

Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488 Veteran Garage Door Repair | Keller TX | 817-769-8488
Veteran Garage Door Repair

204 S Main St Ste 105
Keller,TX
76248
817-769-8488

Garage Door Opener Repair You might find that your garage door opener has actually been giving you problems, so you require to fix it. You can fix it by changing a circuit board, a photo-eye sensing unit, the main drive gear, or the set-limit switches. You can likewise examine if the safety and security sensing…

Leave a Reply

Your email address will not be published. Required fields are marked *